2025 Realistic Verified Free Supermicro SMI300XE Exam Questions
SMI300XE Real Exam Questions and Answers FREE
NEW QUESTION # 10
Which of the following are important safety precautions when removing the GPU tray?
- A. All of the above.
- B. For your own safety, and the safety of the system, two people should remove the tray which weighs more than 70 pounds.
- C. Unnecessary movement can damage the fans below the GPU tray.
- D. Keep the tray straight to prevent it from tilting up or down, which can damage the upper and lower portion of the chassis.
Answer: A
Explanation:
Whenremoving the GPU trayin anMI300X system, the following precautions must be taken:
* Two people should remove the trayas itweighs over 70 pounds, making it unsafe for one person to handle.
* Keeping the tray straightprevents it fromtilting, which candamage the chassis components.
* Unnecessary movement can damage cooling fansdirectly beneath the GPU tray.
Since all the above precautions arecritical for safe removal, thecorrect answer is D (All of the above).
NEW QUESTION # 11
The ROCm commands are not providing output or are failing. What could be the primary reason why?
And how can you validate the reasoning?
- A. If more than 3 GPUs are missing, then ROCm commands will not function. We need to verify that the 3 are missing in the IPMI GUI and review the GPU component section to make sure that at least 2 or fewer GPUs are missing.
- B. You suspect there are GPUs not detected. To determine which GPUs are missing, open the IPMI GUI and review the GPU component section to make sure all GPUs are present.
- C. CPU is not installed correctly on the server. Review the OS dmesg logs for any odd CPU messages, then if located proceed to reseat the CPU.
- D. The GPU baseboard may not be detected. You can determine this by opening the IPMI GUI and reviewing the FW section.
Answer: B
Explanation:
IfROCm commands fail to provide output, the primary issue is likelymissing or undetected GPUs. The best way to validate this is by checking the IPMI GUI and reviewing the GPU component sectionto ensure that all GPUs are present.
* Option A (Correct):Missing GPUsare the most common causeof ROCm failures. The IPMI GUI provides visibility into which GPUs are detected.
* Option B (Incorrect):CPU misalignment would causegeneral system failure, not ROCm-specific issues.
* Option C (Incorrect):The GPU baseboard status can be checked in IPMI but isnot the primary cause of ROCm failures.
* Option D (Incorrect):ROCm can function with multiple missing GPUs, butthe key issue is confirming GPU presence first.
NEW QUESTION # 12
If you need to replace a failed GPU in an MI300X system, what must you do to gain access to the GPUs in the system?
- A. Use the LSPCI command.
- B. Update the AMD command.
- C. Remove the GPU tray.
- D. Configure the SCC.
Answer: C
Explanation:
Toaccess and replace a failed GPUin theMI300X system, you mustremove the GPU tray.
* Option A (Incorrect):UpdatingAMD commandsdoes not physically grant access to GPUs.
* Option B (Incorrect):LSPCIis used tolist PCI devices, not to physically access the GPUs.
* Option C (Incorrect):SCC configurationis unrelated to physical GPU replacement.
* Option D (Correct):Removing the GPU trayis the only way tophysically access and replace GPUs.
NEW QUESTION # 13
What tool is needed to remove the GPU in the MI300X system?
- A. Security Torx Bit
- B. Phillips Head Screwdriver
- C. T15 Torx Bit
- D. T20 Torx Bit
Answer: C
Explanation:
TheGPU in the MI300X systemis secured withT15 Torx screws, requiring aT15 Torx Bitfor removal.
* Option A (Incorrect):T20 Torx Bit istoo largefor GPU screws.
* Option B (Incorrect):Security Torx Bit isnot requiredfor standard GPU removal.
* Option C (Correct):T15 Torx Bit is the correct toolfor removing GPU screws.
* Option D (Incorrect):Phillips Head Screwdriversdo not fit the GPU screws.
NEW QUESTION # 14
What is the main reason the AGFHC tool is not functioning properly?
- A. Missing 1 or more GPUs in the system.
- B. CPU 2 is missing and the AGFHC requires 2 CPUs.
- C. PSU needs to be reseated.
- D. Missing 1 DIMM in the system.
Answer: B
Explanation:
TheAGFHC tool requires a dual-CPU setupto function properly. IfCPU 2 is missing, the toolfails to operate correctly.
* Option A (Incorrect):Thetool does not depend on DIMM configuration.
* Option B (Incorrect):Missing GPUscan cause errors, butthe tool can still function.
* Option C (Correct):AGFHC requires both CPUsto be installed.
* Option D (Incorrect):PSU reseating isnot requiredfor AGFHC operation.
NEW QUESTION # 15
How would you identify and differentiate a failed GPU that needs to be replaced from other GPUs in the system that are functional?
- A. By the discoloration
- B. By the part number
- C. By the serial number
- D. By the warning light
Answer: D
Explanation:
A failed GPU in the Supermicro MI300X system can be identified usingthe warning light indicator.
Supermicro systems includeLED diagnostic indicatorsthat display the operational status of various components, including GPUs. When a GPU malfunctions, the system will trigger an alert that is displayed as a warning light on the GPU tray or the server chassis. This allows technicians to visually identify the faulty GPU without requiring extensive hardware testing.
* Discoloration (A)is not a reliable method of identifying a failed GPU as it would require physical degradation, which is uncommon.
* Serial numbers (B)andPart numbers (C)are used for inventory tracking but do not indicate functional status.
* Warning lights (D)are the recommended method, as documented in the system health monitoring section of Supermicro's documentation, which detailsLED indicators and diagnostic lights for system status monitoring.
NEW QUESTION # 16
Before disconnecting the cables from the NVMe backplane, you should map or take a picture of the cables to ensure they are returned to the same locations. True or False?
- A. True
- B. False
Answer: A
Explanation:
When working withSupermicro MI300X GPU systems, it ishighly recommendedtomap or take a picture of cable connections before disconnection.
Reasons:
* Ensuring Proper Reconnection# NVMe backplanes have multiplecritical connections(MCIO cables, power cables, data lanes, and SAS connections). Misplacing any of these cables could cause:
* Boot failures
* Drive detection issues
* Performance degradation
* Avoiding Errors in Cable Routing# Supermicro documentation states thatimproperly routed cables can obstruct airflow, potentially leading tooverheatingin high-performance systems.
* Easing Future Troubleshooting# If issues arise after reassembly, aphoto or cable mapallows engineers toquickly verifywhether cables werereconnected properly.
This best practice isofficially recommendedinSupermicro's service and installation guidelinesfor NVMe backplanes.
NEW QUESTION # 17
Which 2 ROCm commands should you run to gather AMD GPU information from the server?
- A. sudo rockm-smc, and sudo rockm-bug.report.txt
- B. sudo rocm-smi -a, and sudo rocm-smi
- C. sudo rocm-gpu, sudo rocm-baseboardgpu
- D. sudo rocm-csv, and sudo rocm-amd.bug.txt
Answer: B
Explanation:
TheROCm System Management Interface (rocm-smi)is the recommended tool forgathering AMD GPU informationfrom the server.
* Option D (Correct):
* sudo rocm-smi -a displaysall available GPU information.
* sudo rocm-smi showsbasic GPU stats.
* Option A (Incorrect):These arenot valid ROCm commands.
* Option B (Incorrect):"rockm-smc" and "rockm-bug.report.txt"do not exist in ROCm.
* Option C (Incorrect):"rocm-gpu" and "rocm-baseboardgpu" arenot standard AMD diagnostic commands.
NEW QUESTION # 18
Which SUM command is used to verify the AOC NIC installed on the system?
- A. sum.exe -i 10.1.1.100 -u ADMIN -p ADMIN -c getaocinfo
- B. sum.exe -ip 10.1.1.100 -user ADMIN -pass ADMIN -command getnicinfo
- C. sum.exe -i 10.1.1.100 -u ADMIN -p ADMIN -c getaocnicinfo
- D. sum.exe-read all AOC-from 10.1.1.100
Answer: A
Explanation:
Toverify the AOC NIC installedon the system, the correctSUM (Supermicro Update Manager) command is:
css
CopyEdit
sum.exe -i 10.1.1.100 -u ADMIN -p ADMIN -c getaocinfo
* Option B (Correct):This command retrievesAOC NIC information.
* Option A (Incorrect):"getaocnicinfo" isnot a valid command.
* Option C (Incorrect):This syntax isincorrect and will not execute properly.
* Option D (Incorrect):"getnicinfo" retrievesgeneral NIC details, not AOC NIC-specific information.
NEW QUESTION # 19
What will happen when you pull the GPU tray out partially?
- A. The tray will start becoming very hot.
- B. The tray will start spewing liquid everywhere.
- C. The tray will lock to prevent it from pulling too fast, and 1 person on each side of the tray needs to press down on the lever to unlock it.
- D. The tray will vibrate three times, alerting the user that it is released from the rail mechanism and is ready to be lifted, then start flashing a red light.
Answer: C
Explanation:
When theGPU tray is pulled out partially, itlocks in placetoprevent accidental removal or dropping. To fully remove it,two people must press down on the lever on each sidebefore continuing.
* Option A (Correct):Thetray locks automaticallyto ensure safe removal, and two people are needed to press the unlock levers.
* Option B (Incorrect):Thetray does not vibrate or flash redwhen released.
* Option C (Incorrect):Thetray does not contain liquid components.
* Option D (Incorrect):Thetray does not generate excessive heat upon removal.
NEW QUESTION # 20
The AGFHC Tool is intended for use exclusively by specific users. Who are those users? Choose 2 answers.
- A. SMC Partners
- B. VARs / Resellers
- C. Customers
- D. Internal SMC Employees
Answer: B,D
Explanation:
TheAGFHC Toolis specifically designed forSupermicro's internal employeesandauthorized resellers (VARs). These users require access to diagnostic and firmware update tools that are restricted totrained personnel.
* Option A (Correct):Internal Supermicro employeesuse this tool for system maintenance and diagnostics.
* Option D (Correct):VARs (Value-Added Resellers)are authorized to use the tool forcustomer support and system integration.
* Option B (Incorrect):GeneralSMC partners do not have accessto AGFHC.
* Option C (Incorrect):End customers do not have accessto this tool.
NEW QUESTION # 21
The ROCm commands are not providing output or are failing. What could be the primary reason why?
And how can you validate the reasoning?
- A. If more than 3 GPUs are missing, then ROCm commands will not function. We need to verify that the 3 are missing in the IPMI GUI and review the GPU component section to make sure that at least 2 or fewer GPUs are missing.
- B. You suspect there are GPUs not detected. To determine which GPUs are missing, open the IPMI GUI and review the GPU component section to make sure all GPUs are present.
- C. CPU is not installed correctly on the server. Review the OS dmesg logs for any odd CPU messages, then if located proceed to reseat the CPU.
- D. The GPU baseboard may not be detected. You can determine this by opening the IPMI GUI and reviewing the FW section.
Answer: B
Explanation:
IfROCm commands fail to provide output, the primary issue is likelymissing or undetected GPUs. The best way to validate this is by checking the IPMI GUI and reviewing the GPU component sectionto ensure that all GPUs are present.
* Option A (Correct):Missing GPUsare the most common causeof ROCm failures. The IPMI GUI provides visibility into which GPUs are detected.
* Option B (Incorrect):CPU misalignment would causegeneral system failure, not ROCm-specific issues.
* Option C (Incorrect):The GPU baseboard status can be checked in IPMI but isnot the primary cause of ROCm failures.
* Option D (Incorrect):ROCm can function with multiple missing GPUs, butthe key issue is confirming GPU presence first.
NEW QUESTION # 22
Which SUM command is used to check basic system information?
- A. sum.exe -I 10.1.1.100 -u ADMIN -p ADMIN -c checkassetinfo
- B. sum.exe -ip 10.1.1.100 -user ADMIN -pass ADMIN -command checksysteminfo
- C. sum.exe call system information
- D. sum.exe -i 10.1.1.100 -p ADMIN -u ADMIN -c checkbasicinfo
Answer: D
Explanation:
TheSUM (Supermicro Update Manager) command to check basic system informationis:
css
CopyEdit
sum.exe -i 10.1.1.100 -p ADMIN -u ADMIN -c checkbasicinfo
* Option A (Correct):This is the correct syntax for retrievingbasic system information using SUM.
* Option B (Incorrect):The syntaxis incorrect and will not execute properly.
* Option C (Incorrect):The"checksysteminfo" command is not validin SUM.
* Option D (Incorrect):"checkassetinfo"retrieves system asset details, not basic system information.
NEW QUESTION # 23
......
Exam Dumps SMI300XE Practice Free Latest Supermicro Practice Tests: https://www.testpassking.com/SMI300XE-exam-testking-pass.html
SMI300XE Exam Questions | Real SMI300XE Practice Dumps: https://drive.google.com/open?id=1_nPwAjSVAyxrptlcgxbjlHGOIEU7uaPv